59.F0 Error On HP LaserJet Printers [Solved]

Do you have an HP color laserjet printer and are experiencing the 59.f0 error? If so, don’t worry – you’re not alone! This is a common error that can occur on many different models of HP printers, especially for HP Color LaserJet M452Nw, M277, and M477dw.

In this guide, we will discuss what causes the HP 59.f0 error and how to fix it. We will also provide some tips to help prevent this error from happening in the future.

Basic Printer Checkup

Before you start troubleshooting the 59.f0 error, it’s a good idea to do a basic printer checkup on your HP printer. This can help identify any potential problems that may be causing your HP laserjet printer to malfunction. Here are a few things you can do to get started with the basic printer checkup.

1. Turn on your HP laserjet printer.
2. Check your printer screen, it should not have any display or button issue.
3. Now, place any document on your scanner glass, then click on the copy button. It does not matter if you copy in black or copy in color. You may select either one of them.

If you can copy successfully, you can proceed to the more advanced troubleshooting steps below.

If you cannot copy from your printer, then you have a much bigger problem and you might need to investigate further.

How To Fix 59.f0 Error On My Printer

Now that you’ve done a basic checkup of your printer, it’s time to start troubleshooting the 59.f0 error. There are a few different things you can try to fix this error.

Restart Your Printer

One simplest and most effective way to fix many printer errors is to simply turn off your printer. We highly recommend doing a hard reset.

To do this, you just unplug the power source at the back of your HP printer and wait a couple of minutes before you insert back the plug into your printer and turn it back on.

Check Your Toner Cartridges

If you’ve recently replaced your toner cartridges or installed a new one, this could be the root cause of your 59.f0 error. We recommend checking to see if the toner cartridge is properly seated in its slot and that there are no loose wires or connections.

You should also check the expiration date on your toner cartridge. If it’s been more than six months since you last replaced it, the toner might be dried out and causing the error. In this case, you’ll need to replace the toner cartridge. To ensure that you are only using HP genuine toners, check these items out.

No products found.

Update Your Printer Firmware

If you’re still experiencing the HP 59.f0 error after restarting your printer and checking your toner cartridges, it’s time to try updating your printer firmware. Firmware is the software that controls your printer and tells it how to function.

Sometimes, there are bugs in the firmware that can cause your printer to display errors or behave erratically. By updating your printer firmware, you can often fix these issues.

To update your printer firmware, you’ll need to go to the HP website and download the latest version of the firmware for your printer model. Once you’ve downloaded the firmware, follow the instructions on how to install it on your printer.

If you’re still having trouble with the 59.f0 error after trying all of these troubleshooting steps, we recommend doing our expert fix for the 59.f0 error code.

Advanced Troubleshooting Steps To Fix 59.f0 Error On HP Printer

If you’ve tried the steps above and you’re still getting the 59.f0 error on your HP Color LaserJet M452Nw, M477dw, or M277, you can try resetting the Intermediate Transfer Belt or the ITB. This is a process that will require you to open up your printer and access the main board.

We recommend doing this only if you’re comfortable opening up your printer and working with electronic components. If you’re not comfortable, we recommend taking your printer to a professional for service.

To fix the HP printer error 59.f0, check all of its internal connections such as those on ITB and sensor. Make sure they’re tight too! If everything looks good then try resetting it by following these steps:

Total time to fix 59.f0 error: 30 minutes

Access the inside of your HP printer.

Open the access door on the right of your HP printer.

Locate the intermediate transfer belt.

Hold the blue lever inside and carefully pull it on both ends of this transfer belt assembly. You’ll need to pull it towards you for easy access so make sure you’re doing it correctly!

Look for two large handles.

Once you’ve pulled out enough of the transfer belt, two large handles should pop free.

Remove the transfer belt

Hold both large handles on the transfer belt and pull until it is completely free from its connection.

Installing the new ITB

The new transfer belt should be installed in reverse order. Be careful not to touch the surface of your transfer belt while installing it. This can cause some serious damage to your HP printer.

Setting up the newly installed ITB

Go to the “Control Panel” of your HP printer and press the “Home” button, so you can start resetting the New Transfer Kit Setting. At the “Administration” menu, click on “Manage Supplies”.

Make sure the New Transfer Kit is detected

Click on the “Rest Supplies” option and then choose “New Transfer Kit.” Click on Yes and OK, respectively.

Do a printer calibration

After you have replaced the transfer belt to fix the 59.f0 error, you need to perform a full calibration of your HP printer. Calibration ensures that your printer’s colors are accurate, consistent, and of the highest quality.

Testing The ITB To Ensure HP 59.f0 Error Fix Works

There are a few ways to test your Intermediate Transfer Belt. One way is by rotating the gears and checking for any fluctuations in the flag when you turn the white gear, if there’s an issue with it then replace it with a new ITB.

If the ITB is not damaged after checking, proceed with examining the Sensor SR9. The location of Sensor SR9 in your HP printer is inside the ITB Cavity. On your printer’s control panel, proceed to click on the home button and look for the Diagnostics menu. Look for Manual Sensor Test and click the “OK” button.

Once you release the SR9 flag from inside of the ITB cavity, check to see if your sensor responds by pressing down on it. If not then sensor replacement may be needed or something else might have happened that caused this problem on your HP printer. If you’re still having trouble, we recommend taking your printer to an HP service center near you.

Last update on 2023-04-09 / Includes affiliate links / Images from Amazon.com